To assist in deciding whether a specific stone is appropriate for certain uses, the coding system below was developed and corresponds with the charts on the following pages for all available natural stone.
|Not recommended in wet areas.|
|Can be used in interior wet wall areas, if sealed and maintained properly. If not properly maintained, the stone look could be altered. Please contact your sealer manufacturer or your Daltile sales representative for information about products that can protect the stone from moisture exposure.|
|Might contain dry seams, pits, fossils and glass veins that are filled at the factory or during installation. These are all inherent characteristics of the stone. Since these voids can sometimes lose their fillings, they should be refilled as part of normal maintenance.|
|A sealer is recommended. (Note: Some stones, such as limestone and tumbled stone among others, should be sealed prior to grouting.)|
|These stones contain deposits of minerals and iron that may react to moisture. Stone bleeding or rusting is a common example of this. These stones should not be used in installations where they would be exposed to standing, run-off water or too much humidity. A sealer is strongly recommended but will not prevent the chemical reaction from happening. Contact your sealer manufacturer or Daltile sales representative for information about products that can protect the stone from moisture exposure.|
|White setting materials are recommended.|
|Install with a non-staining epoxy. Do not use any water-based setting material with these stones.|
|Not recommended for shower floors.|
|Medium bed mortar is required for tiles with at least one side greater than 15".|
|These stones may change color over time if exposed to direct sunlight.|
|Use a temporary water soluble grout release during installation.|
|The slip resistance of natural stone tiles vary. Caution should be used in determining if the selected stone will be sufficiently slip resistant for exterior use.|
|Refer to the "Special Limestone Installation Guide".|
|L||Low: Background color is relatively uniform.|
|M||Medium: Background color contains slight variations.|
|H||High: Background color contains distinct variations.|
|R||Random: Variegated in color and veining. Blending allowances during installation are strongly recommended.|
Natural stone products inherently lack uniformity and are subject to variation in aesthetics (color, shade, finish, etc.) and performance (hardness, strength, slip resistance, etc.). Natural stone products do not meet minimum coefficient of friction thresholds recommended by safety standard setting organizations. No warranties, expressed or implied, relative to merchantability or fitness for a particular purpose are made regarding the natural stone products distributed by Daltile. Check local building codes prior to specification or installation to verify that product technical characteristics comply with required parameters.
NOTE: The existence and dimensions of a bevel may vary from lot to lot. Be sure to request a sample of the specific lot you are planning to order, if the bevel is an important feature for your job.
|Suitable for uncovered exterior floor and wall applications in freezing andnon-freezing climates.|
|Suitable for uncovered exterior wall applications in freezing and non-freezing climates.|
|Suitable for uncovered exterior floor and wall applications in non-freezing climates only.|
|Suitable for uncovered exterior wall applications in non-freezing climates only.|
|EF||Suitable for covered* exterior floors in freezing and non-freezing climates.|
|EW||Suitable for covered* exterior walls in freezing and non-freezing climates.|
|SF||Suitable for covered* exterior floors in non-freezing climates only.|
|SW||Suitable for covered* exterior walls in non-freezing climates only.|
|N/A||Not recommended for exterior applications.|
*Covered implies an area protected from the elements. Natural stone products are not recommended for any wet areas where they may be exposed to chemicals such as waterlines and pools, or to extreme humidity and heat, such as steam rooms, among others.
|N/A||Not recommended for floor use.|
|1||Residential: Suitable for residential use. Not recommended for commercial areas.|
|2||Medium/Light Commercial: Suitable for light commercial and residential use.|
|3||Heavy Commercial: Suitable for most commercial and/or high traffic areas.|
NOTE: Polished surfaces are not recommended for floor areas where slip resistance is a concern. Our durability recommendations are only based on the technical characteristics of the stones, however, slip resistance shall still be taken into consideration when selecting the product for a specific application. Natural stone products do not meet minimum coefficient of friction thresholds recommended by safety standard setting organizations.
Group A: Sound stones with no geological voids or fissures. These stones do not require any filling or patching.
Group B: Similar to Group A, but geological imperfections could be evident. These stones may contain holes or voids, which are filled with epoxy or resin.
Group C: These stones may contain holes, voids, lines of separation and structural flaws. It is standard practice to repair these stones by filling them or reinforcing them.
Group D: Similar to Group C but these stones contain larger natural faults and require more refinishing over time.
Soundness is meant to help classify denser stones (Group A and B) from more fragile stones (Group C and D). Stones classified under Groups C and D may require additional fabrication before, during or after installation as part of regular maintenance.